Hisilicon Bricked Boxes Recovery

Discussion in 'Android Boxes' started by raza05, Oct 28, 2019.

Tags:
  1. raza05

    raza05 Active Member

    Messages:
    140
    Likes Received:
    223
    Trophy Points:
    43
    Gender:
    Male
    Recovery of Hislicon based android devices is pretty much tricky as it is both simple & difficult at the same time .There is no exact known method of forced recovery like Amlogic except to remove the emmc from main board & erase/write it by Programmers
    However the simple method is to use Hitool program .it helps to erase the flash & write it again the step taken are as follows
    1. Download Hitool program & install on your PC please install Java(Ver 1.8), then you can execute this

    2. Now open Hitool

    9.png


    3.Select HiBurn , you have to select Device ID to erase EMMC.. Select Hi3798CV200.(if your processor is Hi3798Cv200 otherwise select your relevant device ID )

    4.After select Hi3798CV200, then you will see below picture,

    8.png


    5. Now, ready to erase EMMC.
    6. Connect RS232 cable to PC to your Box ( you have to look if your Box supports RS232)
    7. If you have connect RS232 cable to PC to Box then it is ready to erase EMMC
    8 . Carefully select if you want to “Erase” just Partition or Erase All ..I recommend to use the first option “Erase” if it doesn’t work then use Erase All”
    Before pressing "Erase All" button, please check that you select "Burn EMMC"

    10a.PNG


    9. Turn on Box power Then you will see the message press OK to erase Emmc. It will Erase the Emmc .Initialization window will appear

    11.png


    10. Now Copy the recovery Image files you have downloaded for you box to USB stick .In most cases you can find 4 files. Recommend to format your USB Stick with FAT32.
    11. Insert USB stick to Front USB 2.0 port and turn AC power ON, then you will see "uPdt" message on Front panel It means that box is updating with firmware.
    It will takes over 3 minutes for all procedures.
     
    Last edited: Oct 28, 2019
    tomi54, Aliraza63 and Johnny B. like this.
  2. Lovitch

    Lovitch New Member

    Messages:
    8
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    I have a problem in the device which is when I want to pass a picture by usb and when I put it in the device and then I switch it off from the back and restart it and I pressed the power button from the front gives me the window, but then the device cramps and does not respond to the control machine
     
  3. Lovitch

    Lovitch New Member

    Messages:
    8
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    Can this solution restore the octagon sf 8008 to recovery, or is it for my android devices
     
  4. raza05

    raza05 Active Member

    Messages:
    140
    Likes Received:
    223
    Trophy Points:
    43
    Gender:
    Male
    ..Unable to help you unless know what kind of picture you were trying to Pass ...& which box you are using Chip version ,android version etc ..if possible capture a screen shot & post
     
    Johnny B. likes this.
  5. Lovitch

    Lovitch New Member

    Messages:
    8
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    أهلا بك

    جهازي ليس Android ولكن يعمل على نظام lunix

    Translated..

    welcome

    My device is not Android but runs on Linux
     
    Last edited by a moderator: Mar 15, 2020
  6. Lovitch

    Lovitch New Member

    Messages:
    8
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    Sorry but the picture link from l.top4top.io has been marked as unsave, best is to upload your picture to another site or just upload it to here.
     
    Last edited by a moderator: Mar 15, 2020
  7. Lovitch

    Lovitch New Member

    Messages:
    8
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
  8. raza05

    raza05 Active Member

    Messages:
    140
    Likes Received:
    223
    Trophy Points:
    43
    Gender:
    Male
    Ok so far I understand by picture you mean Image ...if your box is not picking the image from usb drive change the the drive least size 4GB
     
    Johnny B. likes this.
  9. Lovitch

    Lovitch New Member

    Messages:
    8
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    I have usb 4g and i find the same problem
     
  10. raza05

    raza05 Active Member

    Messages:
    140
    Likes Received:
    223
    Trophy Points:
    43
    Gender:
    Male
    Johnny B. likes this.
  11. Lovitch

    Lovitch New Member

    Messages:
    8
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    شكرا لك ساجرب

    Thank you, I'll try
     
  12. tomi54

    tomi54 Member

    Messages:
    48
    Likes Received:
    19
    Trophy Points:
    8
    Gender:
    Male
    Location:
    valencia spain
    Good morning, you will know to tell me what cable is actually necessary to put it through rs232

    greetings and thank you very much comrades.
     
  13. tomi54

    tomi54 Member

    Messages:
    48
    Likes Received:
    19
    Trophy Points:
    8
    Gender:
    Male
    Location:
    valencia spain
    Last edited: Apr 20, 2020
  14. Lovitch

    Lovitch New Member

    Messages:
    8
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    The problem was resolved in the new multiplayer system
     
  15. tomi54

    tomi54 Member

    Messages:
    48
    Likes Received:
    19
    Trophy Points:
    8
    Gender:
    Male
    Location:
    valencia spain
    Good, sorry but I do not understand, you want to say thank you, greetings.
     
  16. tomi54

    tomi54 Member

    Messages:
    48
    Likes Received:
    19
    Trophy Points:
    8
    Gender:
    Male
    Location:
    valencia spain
    I already have it clear what cable to use, in fact I already did it greetings and thanks
     

    Attached Files:

    abohabab and Johnny B. like this.
  17. abohabab

    abohabab New Member

    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    starSat X1 Pro 4K Ultra has stopped on the message of Dimux Initial Failed and I want to use the HiTool program to retrieve it, and I do not have the EMMC HI3798MV200 ( 4 FILES) flash program. I hope you can help me to obtain the required files, thank you
     
  18. raza05

    raza05 Active Member

    Messages:
    140
    Likes Received:
    223
    Trophy Points:
    43
    Gender:
    Male
    Johnny B. likes this.