Galaxy Innovations S3158se

Discussion in 'Other satellite receivers.' started by tinoco, Oct 29, 2020.

  1. tinoco

    tinoco New Member

    Messages:
    17
    Likes Received:
    1
    Trophy Points:
    3
    Gender:
    Female
    good afternoon everyone here in this were already worked with this box that appeared to me here in my house one Galaxy Innovations s3158se with the latest firmware I changed the firmware to Official with the USB stick because the box is working badly everything went well but now when I unplugged the box and reconnected the box now it only has the hours on the display I already tried to upgrade by rs232 cable with the program New Ali Upgrade ALI 3606 I'm not able to connect with the box any help would be grateful thanks
     
  2. Johnny B.

    Johnny B. Technical Support Staff Member Moderator

    Messages:
    2,269
    Likes Received:
    1,026
    Trophy Points:
    113
    Gender:
    Male
    Location:
    Netherlands
    Home Page:
    Sorry but it's for me the first time that I hear about these Galaxy Innovations s3158se receivers but often it's related to the version boot loader and firmware you installed.

    For example, you have a boot loader 1.1.6 which is a old one, and you install a newer firmware, then it may not work.

    However, be aware that this is just a thought what it could be, I do not own this box, never had one, thus by doubt, then it's better to wait for someone else which has more experiences with these type of receiver.
     
  3. tinoco

    tinoco New Member

    Messages:
    17
    Likes Received:
    1
    Trophy Points:
    3
    Gender:
    Female
    ok friend thank you very much but if there is anyone can help me I would say goodbye
     
  4. Aliraza63

    Aliraza63 Active Member

    Messages:
    83
    Likes Received:
    114
    Trophy Points:
    33
    Gender:
    Male
    Box needs to upgrade to its Erom .
    Software , loader and method attached .
     

    Attached Files:

    toysoft, raza05 and Johnny B. like this.
  5. tinoco

    tinoco New Member

    Messages:
    17
    Likes Received:
    1
    Trophy Points:
    3
    Gender:
    Female
    my bord is the leopardo6 version 2.0 version I have to change the resistance of the 810 to the 805 after updating the box I put it back in the same place where I took it, correct friend.
    thank you so much friend i will try later then i say how my adventure went goodbye.
     
  6. tinoco

    tinoco New Member

    Messages:
    17
    Likes Received:
    1
    Trophy Points:
    3
    Gender:
    Female
    hello guys when changing the resistance of the 805 to the 810 I ended up if I wanted to lost the resistance does anyone know tell me the value of this resistance thanks
     
  7. raza05

    raza05 Active Member

    Messages:
    85
    Likes Received:
    154
    Trophy Points:
    33
    Gender:
    Male
    can you post main board pictures here
     
    Johnny B. likes this.
  8. tinoco

    tinoco New Member

    Messages:
    17
    Likes Received:
    1
    Trophy Points:
    3
    Gender:
    Female
    the main board is at the top
    Manual for EromUpgrade.pdf
     
  9. Johnny B.

    Johnny B. Technical Support Staff Member Moderator

    Messages:
    2,269
    Likes Received:
    1,026
    Trophy Points:
    113
    Gender:
    Male
    Location:
    Netherlands
    Home Page:
    These tiny smd resistors do not have a value code printed on it, thus it's only to say which value it has after measuring it.
    And to do that, you need to find someone which has this motherboard, and has the knowledge/equipment as also be whiling to measure it for you to know for sure which value it has.

    But, when I would be in this situation, and based that it is a switch situation, then my best guess is that it is a zero ohm resistor and if it's so, then you can just add a thin wire instead of a zero ohm resistor.

    Keep in mind that I'm not claim that is is a zero ohm resistor, thus needless to say that you do it on your own risk, but it seems to me the most logic.
     
    raza05 likes this.
  10. tinoco

    tinoco New Member

    Messages:
    17
    Likes Received:
    1
    Trophy Points:
    3
    Gender:
    Female
    I also arrived at the same conclusion that you my friend I think it is really a zero ohm resistor already put it there but then when the program starts to update the box it appears (CHECK SERIAL PORT STATUS) after a few seconds it goes away (WITH TEST ERROR) already checked the rs232 port on my pc both with windows 7 and xp it seems to be ok some help thanks thanks.
     
  11. Johnny B.

    Johnny B. Technical Support Staff Member Moderator

    Messages:
    2,269
    Likes Received:
    1,026
    Trophy Points:
    113
    Gender:
    Male
    Location:
    Netherlands
    Home Page:
    I think..
    Test the serial rs232 port with a serial program as putty in serial mode or the older Hyperterminal from windows.
    See if it gives some readable output from the box and when not, than it could be a damaged rs232 chip on the motherboard which is often happens with receivers.
     
    raza05 likes this.
  12. tinoco

    tinoco New Member

    Messages:
    17
    Likes Received:
    1
    Trophy Points:
    3
    Gender:
    Female
    I think it is this memory chip that is blocked 1PCS M25P64-VMF6P M25P64V6P 25P64V6P 64 Mbit, Low Voltage, Serial Flash Memory so i think i will give up if i can get a cheap one i will still go back to the box if i can't find it i will send it to the trash thanks friends
     
    Johnny B. likes this.