DM800 Sim 2.01 network

Discussion in 'DM800HD Hardware troubles and Repair support.' started by frontonkiller, Oct 17, 2017.

  1. frontonkiller

    frontonkiller New Member

    Messages:
    14
    Likes Received:
    4
    Trophy Points:
    3
    Gender:
    Male
    Hi all I have the dm800 with a huge problem, No network, no local network, no lights on the RJ45

    The problems start, when I conect a Wifi to the USB port, LOL
    and I disable the local network, cause wlan must start at the begining.
    Now Im flashing it, on the RS232 way
    Cause I cant flash it, on network mode... Only in RS232 Mode

    Im Looking for a Photo to describe my face... Wait....

    [​IMG]

    This is normal, I got my feet in the wrong site ?
    Metí la pata in spanish

    Regards
     
  2. Johnny B.

    Johnny B. Technical Support Staff Member Moderator

    Messages:
    2,822
    Likes Received:
    1,504
    Trophy Points:
    113
    Gender:
    Male
    Location:
    Netherlands
    Home Page:
    Maybe reset the bios to fabric settings with a terminal program as Putty or Hyperterminal and using the serial port.
     
  3. frontonkiller

    frontonkiller New Member

    Messages:
    14
    Likes Received:
    4
    Trophy Points:
    3
    Gender:
    Male
    Hi Johnny Is nice to see u again... At this moment Im flashing it...
    do u think this not resolve the problem ?

    I have putty, i use this program to telnet or ssh, but I never get in, on a box using rs232, there's a manual or tutorial ?
    Thanks
     
  4. Johnny B.

    Johnny B. Technical Support Staff Member Moderator

    Messages:
    2,822
    Likes Received:
    1,504
    Trophy Points:
    113
    Gender:
    Male
    Location:
    Netherlands
    Home Page:
    It's not so difficult to do it with Putty,
    Just start it and choose sessions.
    Enable Serial, choose comport (mostly Com 1) and Speed 115200
    Save it if you like or press open.

    To access the bios, when the terminal is active, turn on the box and after a second hold the front push button.
    Other method is, when you press S see in the terminal, press the S key on the keyboard.

    But yes, a new install may solve it, if the bios settings are not changed due switching between the Wifi and network..
     
  5. frontonkiller

    frontonkiller New Member

    Messages:
    14
    Likes Received:
    4
    Trophy Points:
    3
    Gender:
    Male
    the mac is

    FF FF FF FF FF FF

    Im scrubbed
     
  6. Johnny B.

    Johnny B. Technical Support Staff Member Moderator

    Messages:
    2,822
    Likes Received:
    1,504
    Trophy Points:
    113
    Gender:
    Male
    Location:
    Netherlands
    Home Page:
    Telnet your DM800.
    Go to /etc/init.d/bootup and put as first line as follow: "ifconfig eth0 hw ether 00:09:34:26:3E:92" than you can change freely to any MAC address you need.

    Or google search to change mac address dm800hd
    Or install other software may help.
     
  7. frontonkiller

    frontonkiller New Member

    Messages:
    14
    Likes Received:
    4
    Trophy Points:
    3
    Gender:
    Male
    Remember I havent Network I cant use telnet
    I'll go to try... conecting the wlan on the dm800 and then Telnet

    -------------------------------------------------------------------------------------

    Old images havent drivers... wow its difficult with out the local network... this is going down...

    New images 232 way stay on this and not continue

    "box is flashing from its memory..."


    Regards
     
    Last edited: Oct 18, 2017
  8. Johnny B.

    Johnny B. Technical Support Staff Member Moderator

    Messages:
    2,822
    Likes Received:
    1,504
    Trophy Points:
    113
    Gender:
    Male
    Location:
    Netherlands
    Home Page:
    Yeah without network it's not so easy to flash the box by serial, and it's time consuming, I know.
    And most of the lan network issues are mainly related to the cpu, and by using a wifi usb stick you need to have a bit of luck with the drivers, however (I think) Chipset Ralink RT5370 is often recognized in most image files.
     
    toysoft likes this.
  9. frontonkiller

    frontonkiller New Member

    Messages:
    14
    Likes Received:
    4
    Trophy Points:
    3
    Gender:
    Male
    Hi man... I have the box running on my room with the wifi right now...
    Now I can get in with telnet and ftp, But...

    ---------------------------------------------------------------------------------------------

    Telnet your DM800.
    Go to /etc/init.d/bootup and put as first line as follow: "ifconfig eth0 hw ether 00:09:34:26:3E:92" than you can change freely to any MAC address you need.

    I can see the bootup file
    It doesnt exist
     
  10. Johnny B.

    Johnny B. Technical Support Staff Member Moderator

    Messages:
    2,822
    Likes Received:
    1,504
    Trophy Points:
    113
    Gender:
    Male
    Location:
    Netherlands
    Home Page:
    Yeah it probably differ due the type image file and to be honest, I never needed to edit the mac address so I can only tell what I find on the internet.
    And normally, if you add a ip address in the network settings it should generate a mac address, only if it's disabled or not used it may fall back to FF FF FF FF FF FF
    But maybe this..
    Check the var/etc map en see if there is a init file and put this line into the file,
    ifconfig eth0 down; ifconfig eth0 hw ether 00:09:23:47:97:E5; ifconfig eth0 up
    Or try the other.
     
  11. frontonkiller

    frontonkiller New Member

    Messages:
    14
    Likes Received:
    4
    Trophy Points:
    3
    Gender:
    Male
    Hello again... Perfect now
    I follow the steps, INIT file metod
    Now I Have Lan running perfect and Wifi Too

    Thanks man...
     
    Johnny B. likes this.
  12. toysoft

    toysoft Well-Known Member Staff Member

    Messages:
    443
    Likes Received:
    551
    Trophy Points:
    93
    Gender:
    Male
    Location:
    Switzerland
    Home Page:
    If on a DM box (Clone or Original) you get the Hardware RJ45 MAC Address to FF...FF, this means that the Sim card is corrupted,

    TS
     
  13. Johnny B.

    Johnny B. Technical Support Staff Member Moderator

    Messages:
    2,822
    Likes Received:
    1,504
    Trophy Points:
    113
    Gender:
    Male
    Location:
    Netherlands
    Home Page:
    Yeah indeed the mac address will be fall back to FF when a sim card is corrupted, but the network often still works.
    In any case, as for the sim card part, I always look with a terminal if I see if there is a error as, dCA: broken.
    When that appears, then there is as far as I know a sim card issue, or related to it.
     
  14. frontonkiller

    frontonkiller New Member

    Messages:
    14
    Likes Received:
    4
    Trophy Points:
    3
    Gender:
    Male
    Well
    all works fine now...

    I was flashing with serial and recover bad sector metod

    Then I conect the wifi
    telnet and ftp
    ready

    I did the init file, I put on the init file, my mac, I have the mac on the bottom of the dreambox

    REBOOT
    And local network, get the IP, all happy jejeje

    Regards
     
    Johnny B. likes this.
  15. frontonkiller

    frontonkiller New Member

    Messages:
    14
    Likes Received:
    4
    Trophy Points:
    3
    Gender:
    Male
    Hellooooo

    (c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
    Dreambox DM800
    FIRST STAGE 1.00 {BO23456}

    2ND STAGE OK, build #84 (2011-09-02)

    0.000 - BCM board setup
    {00000126,00000126,00000125,00000124,00000123,00000133}
    0.007 - fp init
    0.008 - ca init
    SW != 9000
    error in receive
    error during t1 transfer
    cannot read cert(1)
    SW != 9000
    error in receive
    error during t1 transfer
    cannot read cert(1)
    SW != 9000
    error in receive
    error during t1 transfer
    cannot read cert(1)
    SW != 9000
    error in receive
    error during t1 transfer
    cannot read cert(1)
    SW != 9000
    error in receive
    error during t1 transfer
    cannot read cert(1)
    CA invalid
    OLED found!
    NO CONFIGURATION DATA PRESENT. STOP.
    lcd: * ERR01: NO CA FOUND
    11.132 - load config
    dCA: not existent, loading defaults
    11.163 - config loaded.
    * press to enter setup
    OLED found!
    lcd: BOOT #84
    - read config file: /boot/secondstage.conf
    detected old jffs2 sig.. disable hw ecc
    detected jffs2 blocksize: 16kb
    +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    ++++++++++++++++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
    UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
    dreamupd initialized
    Scanning JFFS2 FS: . done.
    find_inode failed for name=secondstage.conf
    load: Failed to find inode
    - failed to open /boot/secondstage.conf
    lcd: *** SERIAL MODE ***
    entering serial loop...
     
  16. frontonkiller

    frontonkiller New Member

    Messages:
    14
    Likes Received:
    4
    Trophy Points:
    3
    Gender:
    Male
    I pass the NCF repair and

    (c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
    Dreambox DM800
    FIRST STAGE 1.00 {BO23456}

    2ND STAGE OK, build #82 (2011-02-25)

    0.000 - BCM board setup
    {00000126,00000126,00000125,00000124,00000133,00000133}
    0.007 - fp init
    0.008 - ca init
    SW != 9000
    error in receive
    error during t1 transfer
    cannot read cert(1)
    SW != 9000
    error in receive
    error during t1 transfer
    cannot read cert(1)
    SW != 9000
    error in receive
    error during t1 transfer
    cannot read cert(1)
    SW != 9000
    error in receive
    error during t1 transfer
    cannot read cert(1)
    SW != 9000
    error in receive
    error during t1 transfer
    cannot read cert(1)
    CA invalid
    OLED found!
    NO CONFIGURATION DATA PRESENT. STOP.
    lcd: *ERR:NO SIM2xx FOUND
    8.361 - load config
    dCA: not existent, loading defaults
    8.392 - config loaded.
    * press to enter setup
    OLED found!
    lcd: BOOT #82
    - read config file: /boot/secondstage.conf
    detected jffs2 blocksize: 16kb
    +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    ++++++++++++++++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
    UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
    dreamupd initialized
    Scanning JFFS2 FS: . done.
    find_inode failed for name=secondstage.conf
    load: Failed to find inode
    - failed to open /boot/secondstage.conf
    lcd: *** SERIAL MODE ***
    entering serial loop...
     
  17. toysoft

    toysoft Well-Known Member Staff Member

    Messages:
    443
    Likes Received:
    551
    Trophy Points:
    93
    Gender:
    Male
    Location:
    Switzerland
    Home Page:
    Sim card ! Defective or you flashed wrong image for sim in the box.

    TS

    error during t1 transfer
    cannot read cert(1)
    SW != 9000
    error in receive
    error during t1 transfer
    cannot read cert(1)
    SW != 9000
    error in receive
    error during t1 transfer
    cannot read cert(1)
    SW != 9000
    error in receive
    error during t1 transfer
    cannot read cert(1)
    SW != 9000
    error in receive
    error during t1 transfer
    cannot read cert(1)
    CA invalid
    OLED found!
    NO CONFIGURATION DATA PRESENT. STOP.
    lcd: * ERR01: NO CA FOUND
     
    Johnny B. likes this.
  18. frontonkiller

    frontonkiller New Member

    Messages:
    14
    Likes Received:
    4
    Trophy Points:
    3
    Gender:
    Male
    Hellooo, thanks for ur answer

    the owner flash a wrong image, but I cant recover... I pass NFC, turn off the DM800
    Start again, put image for sim201 and nothing
    Error no ca found
    I thinking right now in the SIM, maybe is broken :(
     
  19. toysoft

    toysoft Well-Known Member Staff Member

    Messages:
    443
    Likes Received:
    551
    Trophy Points:
    93
    Gender:
    Male
    Location:
    Switzerland
    Home Page:
    Use JapharFlasher to restore the box, and... if you really want your box to work the best and with the latest drivers... get a Japhar Sim ;o)

    TS
     
  20. frontonkiller

    frontonkiller New Member

    Messages:
    14
    Likes Received:
    4
    Trophy Points:
    3
    Gender:
    Male
    Yeah I used the japhar flasher and nothing happend...
    NCF Repair, japharflasher with image 201
    and NO CA FOUND
    Again and again
    LOL