clon 800 hd error CAinvalid

Discussion in 'DM800HD Hardware troubles and Repair support.' started by malpi, Jun 25, 2017.

  1. Johnny B.

    Johnny B. Technical Support Staff Member Moderator

    Messages:
    819
    Likes Received:
    106
    Trophy Points:
    43
    Gender:
    Male
    Location:
    Netherlands
    Home Page:
    Use the dreamup which in my zipped file, and not the patched version dreamup.
    Also I see on your picture that the local ip is different than the select one, local ip must be the same as the select one.
    If the normal dreamup failed, than there is another cause why it failed.
    Further if you use another system, use a windows Xp system.
     
  2. malpi

    malpi Member

    Messages:
    40
    Likes Received:
    2
    Trophy Points:
    8
    tried with your program and files but nothing is no way to load anything xp
    Yesterday I talked to the owner and asked him for the image he put in that I spoiled the deco.
    The dream is an 800 hd pvr
    He put an image of 800 se
    In case something of this information is worth many thanks
     
  3. Johnny B.

    Johnny B. Technical Support Staff Member Moderator

    Messages:
    819
    Likes Received:
    106
    Trophy Points:
    43
    Gender:
    Male
    Location:
    Netherlands
    Home Page:
    Yeah upload the zipped files I gave you with only the serial port cable connected, use the DreamUp and disable the Use Network option.

    Other option is to use DreamBox OptiFlasher Pro.
    Dream Ip: your dreambox ip.
    Goto Advanced and chose the comport.
    Enable: Repair [No Ca Found] and select Sim2.01 > dm800-sim2.01-ssl84d
    Do Job...
    When finished, you can do the rest with DreamUp, or uploading the image file with Optiflasher
    File is a older DreamBox-OptiFlasher-Pro-E2-v2.0.0.6, SSl-bt files included.

    Note: when starting Optiflasher you may get this warning..
    Snapshot-opt-error.jpg
    Just ignore that, just press ok.
     

    Attached Files:

  4. malpi

    malpi Member

    Messages:
    40
    Likes Received:
    2
    Trophy Points:
    8
    The above has not worked either. Can the bios be reset?
    When started with front button pressed


    (c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
    Dreambox DM800
    FIRST STAGE 1.00 {BE3E3E3E3E3}
    Second stage loader wasn't found. Don't panic - it's not a (real) problem.
    You don't need to repair your Dreambox. It just means that the flashrom with
    the graphical menu was erased. You can restore this with a tool like DreamUp
    with serial access.
    RESCUE{012}
    MICRO2ND OK, build #56 (20080115)
    MAC ADDR: 00 09 34 f1 53 2b
    2.783 - network: 2.784 dhcp
    > dhcp...
    2.813 - starting network
    100 MB Full-Duplex (auto-neg)
    4.447 - httpd, telnetd, dreamupd
    4.450 - ok. start receiving packets
    4.453 - starting dhcp (or manual)
    4.456 - network: 4.458 dhcp
    > dhcp...
    4.460 - dhcp started!
    waiting for DHCP...
    8.520 - got IP address from dhcp
    > 192.168.1.253
    no server address given
    using dhcp address
    no tftp bootfile name was specified, neither manually nor via dhcp. aborting tftp.
    tftp failed.
     
  5. malpi

    malpi Member

    Messages:
    40
    Likes Received:
    2
    Trophy Points:
    8
    I checked the voltage of the sim card
    The pin 1 without the card set gives me a value of 5 v
    With the card set of 1.43v
    It is normal?
     
  6. Johnny B.

    Johnny B. Technical Support Staff Member Moderator

    Messages:
    819
    Likes Received:
    106
    Trophy Points:
    43
    Gender:
    Male
    Location:
    Netherlands
    Home Page:
    No, because with the sim card it needs the 5v, or at least 4v.
    A defective sim card could cause this so that the 5v collapse to a lower voltage, but also a defective Q8 transistor or a bad print track from the Q8 center pin to the sim card pin 1.

    These are a few thing it could be, more info about it see the Sim card issues topic.
     
  7. malpi

    malpi Member

    Messages:
    40
    Likes Received:
    2
    Trophy Points:
    8
    Ok I already have the 5v on pin 1
    The above has not worked either. Can the bios be reset?
    When started with front button pressed


    (c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
    Dreambox DM800
    FIRST STAGE 1.00 {BE3E3E3E3E3}
    Second stage loader wasn't found. Don't panic - it's not a (real) problem.
    You don't need to repair your Dreambox. It just means that the flashrom with
    the graphical menu was erased. You can restore this with a tool like DreamUp
    with serial access.
    RESCUE{012}
    MICRO2ND OK, build #56 (20080115)
    MAC ADDR: 00 09 34 f1 53 2b
    2.783 - network: 2.784 dhcp
    > dhcp...
    2.813 - starting network
    100 MB Full-Duplex (auto-neg)
    4.447 - httpd, telnetd, dreamupd
    4.450 - ok. start receiving packets
    4.453 - starting dhcp (or manual)
    4.456 - network: 4.458 dhcp
    > dhcp...
    4.460 - dhcp started!
    waiting for DHCP...
    8.520 - got IP address from dhcp
    > 192.168.1.253
    no server address given
    using dhcp address
    no tftp bootfile name was specified, neither manually nor via dhcp. aborting tftp.
    tftp failed.
     
  8. Johnny B.

    Johnny B. Technical Support Staff Member Moderator

    Messages:
    819
    Likes Received:
    106
    Trophy Points:
    43
    Gender:
    Male
    Location:
    Netherlands
    Home Page:
    Bios can be reset on several ways..
    1. with optiflasher
    2. with the serial port connected and a terminal as putty or hyperterminal..
    2a. Press the S key on the keyboard after you have turned on the box so turn the box on, wait two counts, press the key.
    2b. Press the front button after you have turned on the box so turn the box on, wait two counts, press the front button.
    These ways should show the bios interface option in the terminal screen.
    Other way, with network and telnet, set the box in stop mode with the front push button and telnet to the box could give access to the bios.

    However.. it's not always reachable because it depends on the image file, or boot loader.
    But with optiflasher advanced, and enable Reset bios factory settings it may work.
     
  9. malpi

    malpi Member

    Messages:
    40
    Likes Received:
    2
    Trophy Points:
    8
    What do I recommend advanced optiflasher payment?
    Could be the solution ?.
     
  10. Johnny B.

    Johnny B. Technical Support Staff Member Moderator

    Messages:
    819
    Likes Received:
    106
    Trophy Points:
    43
    Gender:
    Male
    Location:
    Netherlands
    Home Page:
    Optiflasher, especial the latest version has more option when you have a license, but for basic things as repair no ca found and some more options you need no license.
    And, since it looks as if you only have some software issues, then it should normally be fixed with using only the serial port and uploading the image file and boot loader.
    It's a slow upload process, but it's only needed when the normal method failed.
     
  11. malpi

    malpi Member

    Messages:
    40
    Likes Received:
    2
    Trophy Points:
    8
    With which could load the boot boot?
     
  12. Johnny B.

    Johnny B. Technical Support Staff Member Moderator

    Messages:
    819
    Likes Received:
    106
    Trophy Points:
    43
    Gender:
    Male
    Location:
    Netherlands
    Home Page:
    Not sure what your question is, but assuming that it's related to the boot, and what you need is..
    The boot loader, version depends on what you want to use as image file.
    Suppose you want to use a sim 2.01 ssl76 image file, then you need also to upload a ssl76.nfi boot loader.

    Same story if you want to upload a sim201 ssl84D image file, then you need also to upload the sim201_ssl84D.nfi file boot loader.
    Best method is to upload first the image file, and when it's ready with the upload uploading the boot loader.
     
  13. malpi

    malpi Member

    Messages:
    40
    Likes Received:
    2
    Trophy Points:
    8
    That's the problem there is no way to load anything
    Nor by puerto com nor by lan

    Thank you I have tried everything and there is no way
    thank you very much for your help
     
  14. Johnny B.

    Johnny B. Technical Support Staff Member Moderator

    Messages:
    819
    Likes Received:
    106
    Trophy Points:
    43
    Gender:
    Male
    Location:
    Netherlands
    Home Page:
    If you can't upload a boot loader or image file with the serial connection then it's most likely that your rs232 serial chip u17, the receive part has been defective.
    In that case is replacing it for a new one the only option.

    You need a good working serial connection to the box to fix the software if uploading with the network failed.
    You may also send the motherboard to me for fixing it, but I wonder if it's worth the send cost.
    But if you prefer that, just give me a private message for the details.
     
  15. malpi

    malpi Member

    Messages:
    40
    Likes Received:
    2
    Trophy Points:
    8
    Ok I'm going to change the capacitors I have left but it works because we'll see what I do ok thanks a lot
     
  16. Johnny B.

    Johnny B. Technical Support Staff Member Moderator

    Messages:
    819
    Likes Received:
    106
    Trophy Points:
    43
    Gender:
    Male
    Location:
    Netherlands
    Home Page:
  17. toysoft

    toysoft Member Staff Member

    Messages:
    40
    Likes Received:
    34
    Trophy Points:
    18
    Gender:
    Male
    Location:
    Switzerland
    Home Page:
    Use JapharFlasher instead, check sim to be sure of which one it is and which software you load on the box (for which sim it is).

    https://mega.nz/#!7c4RDSBR!tHuDF-84p1L_VYcCLK2FMiZauIQTBL9uQievaNpLq4U

    TS