Flash the SSL84.NFI file into the box with JapharFlasher (and check to be sure the Network option is turned off). SSL84 DM500HD : Code: http://sources.dreamboxupdate.com/download/7020/secondstage-dm500hd-84.nfi TS
I checked the SIM card was original. I turned on the Netcraft option on the japharflasher but the flashing lights on the back of the box with the lan cable on did not turn on
You need to remove the "v" option of Network when you use JapharFlasher, as you will only use the USB cable from Box to PC. If your RJ45 is broken, it will naturally not turn on the lights on it. Try then the optiflasher, there is a free version, to flash the SSL for it (all is built-in). TS
The lan port was created but it will not accept images with dreamup or Japharflasher, only accept IP images.I hit the image too, but until I turn on the receiver, the headlight turns green for a moment and quickly turns red.
The red-green led, is generally due to the NO CA ERROR message, where you loaded the wrong image into the box or the Sim card is defective. Optiflasher : http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=16380 TS
The SIM card is flawless. I can easily flash with the web browser but with dremup or japharflasher staye on the checksum mode. this version optiflasher not free
Ok, which image are you flashing (name of file nfi and link to download it, so we can check it). Please use the usb cable with Putty software set to 115200 bps and correct COM port to log from the moment you start the box until it stays freezed and give us the log file so we can see the messages the box is giving out. It would help to understand the exact problem. TS
https://feed.newnigma2.to/daily/images/ https://openpli.org/download/dreambox/DM500+HD dreambox-image-dm500hd-20170216.nfi http://images.dream-elite.net/DE4/index.php?dir=DM500HD/&file=Dream-Elite-4.1-dm500hd-20171119.nfi If I can flash with a drem up or jagharflasher or optiflashr (which of course this software requires activation code that I don't have) I think the problem will be solved.
We need more from the log, you can save the full text of the Putty into a file, and attach it here to a post. As it shows for now that the SSL84 is properly loaded and is correct, but then we cannot see what else happens after. On the top left of the Putty window, you have the options and can save all the log into a text file, to attach here to a message. TS
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2020.03.15 04:02:51 =~=~=~=~=~=~=~=~=~=~=~= Code: BCM74050011 012 K1 K2 K3 K4 K5 Shmoo Version=3.2 DDR Freq=0x0000018C %00000001% RC1=00000001 WC1=FFFFFFF8 RC2=00000011 WC2=00000012 RC3=00000009 WC3=FFFFFFF9 RC4=00000009 WC4=0000003A NWC=00000019 RC5=00000001 WC5=00000019 RC6=00000011 WC6=00000019 NRC=00000009 RW=00000011 WW=00000042 G=00000000 R=00000009 W=00000019 BL=00000000 RC1=00000000 RC2=00000010 BL=00000001 RC1=00000000 RC2=00000010 BL=00000002 RC1=00000000 RC2=00000010 BL=00000003 RC1=00000004 RC2=00000012 BL=00000004 RC1=00000000 RC2=00000011 BL=00000005 RC1=00000001 RC2=00000017 BL=00000006 RC1=00000000 RC2=00000014 BL=00000007 RC1=00000000 RC2=00000015 3 COPY CODE COMPARE CODE 4567 (c) 2007,2008 Dream Multimedia GmbH. All rights reserved. Dreambox D M500HD FIRST STAGE 1.0/400 {BO23456} [m 2ND STAGE OK, build #84 (2011-09-01)
It's not enough, there should be more coming after, as it loads the SSL84 and then will continue the loading, so let it continue and after 10 minutes du a copy of all text and attach here in a file to a post, TS
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2020.03.15 04:02:51 =~=~=~=~=~=~=~=~=~=~=~= Code: BCM74050011 012 K1 K2 K3 K4 K5 Shmoo Version=3.2 DDR Freq=0x0000018C %00000001% RC1=00000001 WC1=FFFFFFF8 RC2=00000011 WC2=00000012 RC3=00000009 WC3=FFFFFFF9 RC4=00000009 WC4=0000003A NWC=00000019 RC5=00000001 WC5=00000019 RC6=00000011 WC6=00000019 NRC=00000009 RW=00000011 WW=00000042 G=00000000 R=00000009 W=00000019 BL=00000000 RC1=00000000 RC2=00000010 BL=00000001 RC1=00000000 RC2=00000010 BL=00000002 RC1=00000000 RC2=00000010 BL=00000003 RC1=00000004 RC2=00000012 BL=00000004 RC1=00000000 RC2=00000011 BL=00000005 RC1=00000001 RC2=00000017 BL=00000006 RC1=00000000 RC2=00000014 BL=00000007 RC1=00000000 RC2=00000015 3 COPY CODE COMPARE CODE 4567 (c) 2007,2008 Dream Multimedia GmbH. All rights reserved. Dreambox D M500HD FIRST STAGE 1.0/400 {BO23456} [m 2ND STAGE OK, build #84 (2011-09-01)
You can also before flashing the SSL84.NFI file I told you to flash, activate the BSR, as well as before do a reset of the Bios. See below. Reset Bios : http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=5234#Post5234 BSR (and then flash without rebooting box) : http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=3137#Post3137 TS
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2020.03.15 09:39:06 =~=~=~=~=~=~=~=~=~=~=~= Code: BCM74050011 012 K1 K2 K3 K4 K5 Shmoo Version=3.2 DDR Freq=0x0000018C %00000001% RC1=00000001 WC1=FFFFFFFC RC2=00000010 WC2=00000032 RC3=00000008 WC3=FFFFFFFC RC4=00000008 WC4=00000037 NWC=00000019 RC5=00000001 WC5=00000019 RC6=00000010 WC6=00000019 NRC=00000008 RW=00000010 WW=0000003C G=00000000 R=00000008 W=00000019 BL=00000000 RC1=00000000 RC2=00000010 BL=00000001 RC1=00000000 RC2=00000011 BL=00000002 RC1=00000000 RC2=0000000E BL=00000003 RC1=00000004 RC2=00000012 BL=00000004 RC1=00000000 RC2=00000010 BL=00000005 RC1=00000000 RC2=00000015 BL=00000006 RC1=00000000 RC2=00000013 BL=00000007 RC1=00000000 RC2=00000014 3 COPY CODE COMPARE CODE 4567 (c) 2007,2008 Dream Multimedia GmbH. All rights reserved. Dreambox D M500HD FIRST STAGE 1.0/400 {BO23456} [m 2ND STAGE OK, build #84 (2011-09-01) . 0.017 - BCM board setup 0.018 - fp init 0.018 - ca init 0.515 - load config dCA: not existent, loading defaults 0.542 - config loaded. * press to enter setup lcd: BOOT #84 - read config file: /boot/secondstage.conf detected jffs2 blocksize: 16kb +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ ++++++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU dreamupd initialized Scanning JFFS2 FS: . | / - \ | / - \ | / - \ done. find_inode failed for name=secondstage.conf load: Failed to find inode - failed to open /boot/secondstage.conf - failed to open /cf/autorun.bat USB wait failed. waiting for USB failed! - failed to open /boot/autoexec_dm500hd.bat no valid boot source found. press any key to enter setup. lcd: *** STOP *** lcd: /flash/bootlogo.elf no HDMI device detected no HDMI mode available, reverting to 720p using 1280x720p (60.00 Hz) HDMI using colorspace: 0 create surface 1280 720 Virtual FB Size: 1280x720 BCM74050011 012 K1 K2 K3 K4 K5 Shmoo Version=3.2 DDR Freq=0x0000018C %00000001% RC1=00000001 WC1=FFFFFFFC RC2=00000010 WC2=00000037 RC3=00000008 WC3=FFFFFFFC RC4=00000008 WC4=00000037 NWC=00000019 RC5=00000001 WC5=00000019 RC6=0000000F WC6=00000019 NRC=00000008 RW=0000000F WW=0000003C G=00000000 R=00000008 W=00000019 BL=00000000 RC1=00000000 RC2=00000010 BL=00000001 RC1=00000000 RC2=00000011 BL=00000002 RC1=00000000 RC2=0000000E BL=00000003 RC1=00000004 RC2=00000011 BL=00000004 RC1=00000000 RC2=00000010 BL=00000005 RC1=00000000 RC2=00000015 BL=00000006 RC1=00000000 RC2=00000012 BL=00000007 RC1=00000000 RC2=00000014 3 COPY CODE BCM74050011 012 K1 K2 K3 K4 K5 Shmoo Version=3.2 DDR Freq=0x0000018C %00000001% RC1=00000001 WC1=FFFFFFFC RC2=00000010 WC2=00000037 RC3=00000008 WC3=FFFFFFFC RC4=00000008 WC4=00000037 NWC=00000019 RC5=00000001 WC5=00000019 RC6=0000000F WC6=00000019 NRC=00000008 RW=0000000F WW=0000003C G=00000000 R=00000008 W=00000019 BL=00000000 RC1=00000000 RC2=00000010 BL=00000001 RC1=00000000 RC2=00000010 BL=00000002 RC1=00000000 RC2=0000000E BL=00000003 RC1=00000004 RC2=00000012 BL=00000004 RC1=00000000 RC2=00000010 BL=00000005 RC1=00000000 RC2=00000015 BL=00000006 RC1=00000000 RC2=00000012 BL=00000007 RC1=00000000 RC2=00000014 3 COPY CODE COMPARE CODE 4567 (c) 2007,2008 Dream Multimedia GmbH. All rights reserved. Dreambox D M500HD FIRST STAGE 1.0/400 {BO23456} [m 2ND STAGE OK, build #84 (2011-09-01) . 0.017 - BCM board setup 0.018 - fp init 0.018 - ca init 0.515 - load config dCA: not existent, loading defaults 0.541 - config loaded. * press to enter setup lcd: BOOT #84 - read config file: /boot/secondstage.conf detected jffs2 blocksize: 16kb +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ ++++++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU dreamupd initialized Scanning JFFS2 FS: . | / - \ | / - \ | / - \ done. find_inode failed for name=secondstage.conf load: Failed to find inode - failed to open /boot/secondstage.conf - failed to open /cf/autorun.bat BCM74050011 012 K1 K2 K3 K4 K5 Shmoo Version=3.2 DDR Freq=0x0000018C %00000001% RC1=00000001 WC1=FFFFFFFC RC2=00000010 WC2=00000037 RC3=00000008 WC3=FFFFFFFC RC4=00000008 WC4=00000037 NWC=00000019 RC5=00000001 WC5=00000019 RC6=00000010 WC6=00000019 NRC=00000008 RW=00000010 WW=0000003C G=00000000 R=00000008 W=00000019 BL=00000000 RC1=00000000 RC2=00000010 BL=00000001 RC1=00000000 RC2=00000010 BL=00000002 RC1=00000000 RC2=0000000F BL=00000003 RC1=00000004 RC2=00000011 BL=00000004 RC1=00000000 RC2=00000010 BL=00000005 RC1=00000000 RC2=00000015 BL=00000006 RC1=00000000 RC2=00000013 BL=00000007 RC1=00000000 RC2=00000014 3 COPY CODE COMPARE CODE 4567 (c) 2007,2008 Dream Multimedia GmbH. All rights reserved. Dreambox D M500HD FIRST STAGE 1.0/400 {BO23456} [m 2ND STAGE OK, build #84 (2011-09-01) . 0.017 - BCM board setup 0.018 - fp init 0.018 - ca init 0.513 - load config dCA: not existent, loading defaults 0.540 - config loaded. * press to enter setup lcd: BOOT #84 - read config file: /boot/secondstage.conf detected jffs2 blocksize: 16kb +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ ++++++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU dreamupd initialized Scanning JFFS2 FS: . | / - \ | / - \ | / - \ done. find_inode failed for name=secondstage.conf load: Failed to find inode - failed to open /boot/secondstage.conf - failed to open /cf/autorun.bat