DM900UHD Motherboard pictures

Discussion in 'Schematic drawings, Pcb images etc..' started by Johnny B., Dec 10, 2016.

  1. Johnny B.

    Johnny B. Technical Support Staff Member Moderator

    Messages:
    2,822
    Likes Received:
    1,504
    Trophy Points:
    113
    Gender:
    Male
    Location:
    Netherlands
    Home Page:
    Hmmm I wonder if that part has been stored on the DM900uhd U206 MX25L25635F
    The dm520/525 has a similar serial flash memory chip, but then the 8p version 25L12835F
     
  2. bibic

    bibic Active Member

    Messages:
    108
    Likes Received:
    45
    Trophy Points:
    28
    Gender:
    Male
    My receiver was brick, because I installed original merlin image and not replaced drivers from /lib. I forgot and i restarted receiver. Only mode to rescue my receiver was installed bootloader from dreamboxupdate ( original bootloader from august/ september 2017). Now I have original bootloader and receiver running normal. But image is for sim 2.30.
     
  3. bibic

    bibic Active Member

    Messages:
    108
    Likes Received:
    45
    Trophy Points:
    28
    Gender:
    Male
    The pictures was made today - dm900 sim 2.30
     
  4. toysoft

    toysoft Well-Known Member Staff Member

    Messages:
    443
    Likes Received:
    551
    Trophy Points:
    93
    Gender:
    Male
    Location:
    Switzerland
    Home Page:
    Which tuner is installed in your box ? Dual or the Hybrid one (2 Sat + Terr/Cabl),

    TS

     
  5. bibic

    bibic Active Member

    Messages:
    108
    Likes Received:
    45
    Trophy Points:
    28
    Gender:
    Male
    On first page (#7) i put real pictures; triple tunner Si2169C.
     
    Last edited: Feb 10, 2018
  6. didier.delaey

    didier.delaey New Member

    Messages:
    7
    Likes Received:
    2
    Trophy Points:
    3
    Gender:
    Male
    Hello from didier,
    I have a question about the service connector, is this acting like the db9 serial port from the dm800pvr.
    I suppose is a special cable? or simply acable gong to usb with a different connector like we use for photo downloading?
    regards didier
     
  7. bibic

    bibic Active Member

    Messages:
    108
    Likes Received:
    45
    Trophy Points:
    28
    Gender:
    Male
  8. didier.delaey

    didier.delaey New Member

    Messages:
    7
    Likes Received:
    2
    Trophy Points:
    3
    Gender:
    Male
     
  9. didier.delaey

    didier.delaey New Member

    Messages:
    7
    Likes Received:
    2
    Trophy Points:
    3
    Gender:
    Male
    yes ok I have already the usb to mini model connectors, thank you for the confirmation didier
     
  10. saltydinner

    saltydinner New Member

    Messages:
    2
    Likes Received:
    4
    Trophy Points:
    3
    This is my temporary solution. My new dreambox was reaching 69 degrees celsius. Removing the lid reduced the temperature to 58. Placing a pentium 4 heatsink on top of the original heatsink reduced the temperature to 49 degrees celsius.


    IMG_3044.jpg

    [​IMG]
     
  11. Johnny B.

    Johnny B. Technical Support Staff Member Moderator

    Messages:
    2,822
    Likes Received:
    1,504
    Trophy Points:
    113
    Gender:
    Male
    Location:
    Netherlands
    Home Page:
    That looks very good, thumpupb.jpg
    nice modification, thank you for sharing it.
     
  12. bibic

    bibic Active Member

    Messages:
    108
    Likes Received:
    45
    Trophy Points:
    28
    Gender:
    Male
    Good point. And how did you fit the radiator on the motherboard?
     
  13. saltydinner

    saltydinner New Member

    Messages:
    2
    Likes Received:
    4
    Trophy Points:
    3
    I was just experimenting. The heatsink (radiator) is just sitting on top, not fitted yet. I was thinking about using a thermal pad to stick it on.
     
  14. bibic

    bibic Active Member

    Messages:
    108
    Likes Received:
    45
    Trophy Points:
    28
    Gender:
    Male
    And how remove the original skin? It's hard?
    Thanks for sharing.
     
    Last edited: Sep 23, 2018
  15. Eak_Dumnern

    Eak_Dumnern New Member

    Messages:
    1
    Likes Received:
    1
    Trophy Points:
    1
    Gender:
    Male
    Location:
    Thailand
    Thanks for information, I am newbies so still E2 learning .
     
    Johnny B. likes this.
  16. EnoSat

    EnoSat New Member

    Messages:
    9
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    Location:
    Slovakia
    Hi,
    how to change hwaddr ?
     
  17. toysoft

    toysoft Well-Known Member Staff Member

    Messages:
    443
    Likes Received:
    551
    Trophy Points:
    93
    Gender:
    Male
    Location:
    Switzerland
    Home Page:
    The MAC address is inside the security chip (TPM), you need to replace the sim/TPM chip to change the MAC and Serial number of the box (For example to upgrade your box to a Japhar sim).

    TS
     
    Johnny B. likes this.
  18. EnoSat

    EnoSat New Member

    Messages:
    9
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    Location:
    Slovakia
    now change with setenv command
     
  19. bibic

    bibic Active Member

    Messages:
    108
    Likes Received:
    45
    Trophy Points:
    28
    Gender:
    Male
    Why ?
     
  20. EnoSat

    EnoSat New Member

    Messages:
    9
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    Location:
    Slovakia
    after external reflash 25q64 two device with same MAC