DM900UHD Motherboard pictures

Discussion in 'Schematic drawings, Pcb images etc..' started by Johnny B., Dec 10, 2016.

  1. toysoft

    toysoft Well-Known Member Staff Member

    Messages:
    443
    Likes Received:
    551
    Trophy Points:
    93
    Gender:
    Male
    Location:
    Switzerland
    Home Page:
    Flash the box with the frontpanel method, pressing the frontpanel button that is read (press mostly immediately after you turn on the box) and keep the finger on the button until it finishes flasing red-blue, as it happens on the DM520HD. You could have to try few times, but try again and again until you get that button flashing red-blue and keep until it stops flashing.

    Then you will be in the Rescue Mode and will have an IP address on your TV,

    And flash our image below and let me know if it works,

    OpenPLI 6++ Japhar for Sim 2.30
    MEGA Link :
    Code:
    https://mega.nz/#!ZjgFEa5Y!yuMmAj4kLGjxvIKPn372EcNzLm0Z7wY6EUvaWLIWmhw
    Then let me know how it goes with our DM900UHD OpenPLi 6++ image ;o)

    TS
     
    Johnny B. likes this.
  2. toysoft

    toysoft Well-Known Member Staff Member

    Messages:
    443
    Likes Received:
    551
    Trophy Points:
    93
    Gender:
    Male
    Location:
    Switzerland
    Home Page:
    = frontpanel button that is red
     
  3. bibic

    bibic Active Member

    Messages:
    108
    Likes Received:
    45
    Trophy Points:
    28
    Gender:
    Male
    @toysoft - thanks. But network card is down. No IP. Led network card is off.
     
  4. bibic

    bibic Active Member

    Messages:
    108
    Likes Received:
    45
    Trophy Points:
    28
    Gender:
    Male
    Now I cant get in rescue mode, but led card is on. I have link in router interface, but no ip. Hmmmm!
     
  5. bibic

    bibic Active Member

    Messages:
    108
    Likes Received:
    45
    Trophy Points:
    28
    Gender:
    Male
    I can get in CFE mode. I set ip address, ping ok, but I not have webinterface for install new image, I need bootloader for sim 2.30.
     
  6. bibic

    bibic Active Member

    Messages:
    108
    Likes Received:
    45
    Trophy Points:
    28
    Gender:
    Male
    BOLT> ifconfig eth0 -auto
    100 Mbps Full-Duplex
    Device eth0: hwaddr 00-09-34-xx-xx-xx, ipaddr 192.168.1.10, mask 255.255.255.0
    gateway 192.168.1.1, nameserver 192.168.1.1
    DHCP server 192.168.1.1, DHCP server MAC AC-xx-xx-xx-xx-xx
    *** command status = 0
    BOLT> ping 192.168.1.1
    192.168.1.1 (192.168.1.1) is alive
    192.168.1.1 (192.168.1.1): 1 packets sent, 1 received
     
  7. bibic

    bibic Active Member

    Messages:
    108
    Likes Received:
    45
    Trophy Points:
    28
    Gender:
    Male
    Finaly I succeeded.
    I put on usb stick rescue-dm900.bin (from here - https://board.newnigma2.to/wbb4/ind...20-525-DM820-DM900-DM920-DM7080-USB-Recovery/) ; boot rescue-dm900.bin then receiver go to the rescue and I could to install new image. I installed old backup was made few days ago. After that I wanted to try OpenPLI 6++ Japhar for Sim 2.30, but I can't to the rescue mode. I tryed from telnet (to-the-rescue), with remote control from menu and start receiver with press red button. Nothing. I can't to the rescue mode. Very strange.
     
  8. bibic

    bibic Active Member

    Messages:
    108
    Likes Received:
    45
    Trophy Points:
    28
    Gender:
    Male
    I use the same method and I put openpli from toysoft.It's looks ok. Now I test it.
     
    Johnny B. and toysoft like this.
  9. toysoft

    toysoft Well-Known Member Staff Member

    Messages:
    443
    Likes Received:
    551
    Trophy Points:
    93
    Gender:
    Male
    Location:
    Switzerland
    Home Page:
    For the IP address, it's normal you have problems, most probably your Router/Modem is 1 Gbps, and to get an IP address with the 2.30 clones you need a 100 Mbps Router/Modem, so an old one (don't need to be connected to internet, as you need just IP and network to connect to flash box).

    TS
     
    Johnny B. likes this.
  10. bibic

    bibic Active Member

    Messages:
    108
    Likes Received:
    45
    Trophy Points:
    28
    Gender:
    Male
    But until now always used this router. Suddenly not get Ip. I'll try with old linksys
     
    Last edited: Feb 9, 2018
  11. bibic

    bibic Active Member

    Messages:
    108
    Likes Received:
    45
    Trophy Points:
    28
    Gender:
    Male
    With wrt54gl (100mb) the same situation. Network card not start quick.
    ........
    IT: Entering runlevel: 3
    Configuring network interfaces... [ 5.258105] f0b00000.etherne:01: Broadcom BCM7439 (2) PHY revision: 0x10, patch: 1
    [ 5.260806] f0b00000.ethernet: configuring instance for internal PHY
    [ 5.261613] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    udhcpc: option -h NAME is deprecated, use -x hostname:NAME
    udhcpc (v1.24.1) started
    Sending discover...
    [ 7.263266] libphy: f0b00000.etherne:01 - Link is Down
    Sending discover...
    Sending discover...
    ......
    After this boot normaly, not wait to get ip and recovery mode.
     
  12. toysoft

    toysoft Well-Known Member Staff Member

    Messages:
    443
    Likes Received:
    551
    Trophy Points:
    93
    Gender:
    Male
    Location:
    Switzerland
    Home Page:
    Change cable.

    TS
     
  13. bibic

    bibic Active Member

    Messages:
    108
    Likes Received:
    45
    Trophy Points:
    28
    Gender:
    Male
    All cable is good. I changed of course.
     
  14. toysoft

    toysoft Well-Known Member Staff Member

    Messages:
    443
    Likes Received:
    551
    Trophy Points:
    93
    Gender:
    Male
    Location:
    Switzerland
    Home Page:
    Did you ever successfully flashed my image OpenPLi 6++ Sim 2.30, MEGA link I gave you ? As I don't have DM900UHD boxes, would like to know if that image works. Thanks.

    TS
     
  15. toysoft

    toysoft Well-Known Member Staff Member

    Messages:
    443
    Likes Received:
    551
    Trophy Points:
    93
    Gender:
    Male
    Location:
    Switzerland
    Home Page:
    Be careful that using the FrontPanel Red button is not working every time, as for DM520HD it could be difficult but you need to try again and again, to have it successfully switching to Rescue Mode (Press the Red button once turn on the box, not too early but not too late, then keep pressed your finger on that red button and keep it flashing red-blue until it stops and stays red. It will then show on the TV the IP Address of box in Rescue Bootloader mode).

    TS


     
  16. bibic

    bibic Active Member

    Messages:
    108
    Likes Received:
    45
    Trophy Points:
    28
    Gender:
    Male
    I use all methods; with finger and from putty - to-the-rescue and echo "rescue" >> /proc/stb/fp/boot_mode && reboot
    Receiver not in recovery mode. He does not want at all.
    Your image I installed; it's ok. Has few bugs, but nothing important.
     
    toysoft likes this.
  17. bibic

    bibic Active Member

    Messages:
    108
    Likes Received:
    45
    Trophy Points:
    28
    Gender:
    Male
    Only if your receiver dont go in recovery mode

    For rescue DM900 use usb cable and putty (serial port).

    Start receiver and push ctrl+C to enter in cfe mode. Use usb stick for rescue file downloaded from internet.
    ifconfig eth0 -auto
    show devices
    dir usbdisk0
    boot usbdisk0:zImage-rescue-xxxxx

    Then your receiver get in rescue mode and you can flash firmware.

    Thanks toysoft and johny for help.

    P.S. - toysoft - yourOpenpli image work on dm900 sim 2.30 - https://mega.nz/#!ZjgFEa5Y!yuMmAj4kLGjxvIKPn372EcNzLm0Z7wY6EUvaWLIWmhw . I have not tested too much time. Can put this link on another site? Thanks again.
     
    Last edited: Feb 9, 2018
    AJP007, toysoft and Johnny B. like this.
  18. toysoft

    toysoft Well-Known Member Staff Member

    Messages:
    443
    Likes Received:
    551
    Trophy Points:
    93
    Gender:
    Male
    Location:
    Switzerland
    Home Page:
    Yes, you can repost the link, but pleaase state it's OpenPLi 6++ Japhar Team image modded for Sim 2.30.

    TS

     
    AJP007 likes this.
  19. bibic

    bibic Active Member

    Messages:
    108
    Likes Received:
    45
    Trophy Points:
    28
    Gender:
    Male
    @toysoft - take a look at pictures

    I have original bootloader from dreamboxupdate - zImage-rescue-3.14-r0-dm900-20170801.bin

    I think there was no clone bootloader because the original one can be used. Otherwise I think it had already appeared.
     

    Attached Files:

  20. toysoft

    toysoft Well-Known Member Staff Member

    Messages:
    443
    Likes Received:
    551
    Trophy Points:
    93
    Gender:
    Male
    Location:
    Switzerland
    Home Page:
    If you load the original Bootloader, you box will be stuck/bricked for ever. You will have to send to manufacturer to fix. The bootloader/rescue checks the sim card and if it's not OK, the box is not booting. If you change it and the sim inside the box is not correct even the bootloader/rescue will not start, and you will have bricked your box.

    TS

     
    AJP007 likes this.